Drucken

Kulthifi Blog


Veröffentlicht am von

Richtige Verkabelung / Anschluss der Kabel an der Braun Atelier Anlage A1 oder A2

Gesamten Beitrag lesen: Richtige Verkabelung / Anschluss der Kabel an der Braun Atelier Anlage A1 oder A2

Auch bei der Verkabelung der Braun Anlage mit dem Verstärker A1 oder A2 gibt es einiges zu beachten.

 

 

Aufgrund der vielen Nachfragen stelle ich die richtige Verkabelung in diesem Beitrag dar.

(english version below).

Wie immer ein paar grundlegende Dinge zuerst:

- schalten Sie zuerst alle Geräte aus, bevor Sie mit der Verkabelung beginnen

- für den rechten Kanal nutzen wir die roten Cinch Stecker zur Verkabelung - für den linken Kanal die schwarzen

- bei den Braun Atelier Geräten sind die Buchsen für den rechten Kanal unten - die für den linken Kanal oben

- bei den Lautsprechern ist rot für den "+" Kontakt, schwarz für den "-" Kontakt vorgsehen; bitte achten Sie darauf, dass sie immer richtig verbinden (also + mit + und - mit -)

Auf den Bilder in diesem Beitrag sind folgende Geräte abgebildet (von unten nach oben):

CD Player, Kassettendeck, Tuner, Verstärker, Plattenspieler. Der Typ der Geräte ist hierbei nebensächlich - ich beschreibe hier die Verkabelung für eine typische Braun Atelier Anlage der Serie 1 oder 2, wie ich sie auch in meinem Shop anbiete (hier klicken).

 

Anschluss des CD Players:

Die Cinch Anschlüsse des CD Players (z.B. Braun CD2, CD2/3, CD3, CD4 oder CD5) werden mit den entsprechenden Eingängen am Verstärker verbunden. Am Braun A1 oder Braun A2 nehmen Sie hierfür einfach den Anschluß AUX - oder wenn Sie einen Verstärker A2 der letzten Serie haben, dann können Sie auch den CD Eingang nehmen.

Wenn Sie einen CD3 haben, dann nehmen Sie am besten den FIXED Ausgang am CD3. Dieser liefert ein stabiles Signal. Der daneben liegende variable Ausgang kann (und muss) über den Regler daneben geregelt werden.

 

Anschluss des Kassettendecks / Tape Decks:

Das Kassettendeck können Sie an Tape 1 oder Tape 2 anschließen. 

Dieses Gerät verfügt über 4 Cinch Buchsen an der Rückseite: 2 Ausgänge (Signal geht zum Verstärker) und 2 Eingänge (Signal kommt vom Verstärker, wenn Sie z.B. etwas aufnehmen möchten). Die Ausgänge (Output) am Kassettendeck werden mit den Eingängen  (Tape 1 in) am Braun A1 oder Braun A2 verbunden. Die Eingänge am Kassettendeck (Input) werden mit den Ausgängen am Verstärker (Tape 1 out) verbunden. Achten Sie auch hierbei darauf, dass Sie rechts und links richtig miteinander verbinden.

Anschluss des Tuners / Radios:

Der Tuner wird, wie der Name schon sagt, an die Tuner-Eingänge am Verstärker angeschlossen. Da es nur 2 Cinch Buchsen am Tuner gibt (egal ob Braun T1 oder T2) können Sie hier nichts falsch machen.

Damit der Tuner ein Radiosignal empfangen kann, empfehle ich Ihnen eine UKW Antenne mit Verstärker oder ein hochwertiges Antennenkabel, falls Sie einen Antennenanschluss zu Hause haben. Beides finden Sie hier in meinem Shop.

Anschlüsse am Verstärker:

Am Verstärker schließen Sie jetzt noch die Lautsprecher an die entsprechenden Klemmen an. Rot = Pluspol der Lautsprecher, schwarz = Masse / Minus. Meistens ist eine Ader des Lautsprecherkabels gekennzeichnet (entweder geriffelt oder mit einem farbigen Streifen versehen). Ich verwende diese gekennzeichnete Ader immer für den Pluspol / die rote Klemme.

Bei den Braun verstärkern A1 und A2 sind die Anschlüsse für den linken Lautsprecher oben, für den rechten unten. Achten Sie darauf, dass sich die Kabel nicht berühren. Und pro Klemme auch nur einen Lautsprecher anschließen. Schließen Sie auch die Lautsprecher eines Pärchens an Lautsprecher 1 an; sollten Sie ein zweites Paar Lautsprecher nutzen, dann dieses an Paar 2. Also bitte z.B. NICHT den einen (linken) Lautsprecher an Paar 1 und den anderen (rechten) Lautsprecher eines Lautsprecherpaares an Paar 2. 

Am Verstärker A1 oder A2 sollten Sie dann hinter der Klappe den Schalter für das entsprechende Lautsprecherpaar drücken (meistens Paar 1).

Anschluss des Plattenspielers:

Die Kabel des Plattenspielers sind bei den Braun Plattenspielern P1, P2, P3 und P4 fest montiert. Auch hier ist rot für den rechten Kanal und schwarz für den linken Kanal.

Diese Kabel werden an den Phono Eingang des A1 angeschlossen.

Der A1 hat 2 Phono Eingänge: beide sind für MM Systeme ausgelegt. Es ist daher Ihnen überlassen, ob Sie den Plattenspieler bei Phono 1 oder Phono 2 anschließen. 

Vom Braun A2 gibt es 2 unterschiedliche Versionen:

die erste Version des A2 (auch A2/1 genannt) hat einen Phono MM und einen Phono MC Eingang. Am Phono MM Eingang werden Plattenspieler mit MM System angeschlossen - also in der Braun Welt die Braun Plattenspieler P1, P2, P3 und P4M.

Am Phono MC Eingang wird der P4 mit MC2E System angeschloßen (zu erkennen am Schriftzug "Braun" auf dem Headshell / über der Tonabnehmer Nadel). 

Wenn Sie einen Braun A2/2 haben, dann hat dieser nur noch einen Phono Eingang. Sie schalten dann über den Schalter an der Rückseite zwischen Phono MM und MC um. Stellen Sie den Schalter also einfach entsprechend Ihres Tonabnehmer Systems ein.

Das Anschlusskabel des Plattenspielers hat auch noch ein "Massekabel", also ein einfaches kleines Kabel ohne Cinch Stecker. Dieses wird einfach an die Masseklemme des Verstärkers angeschlossen. Diese befindet sich ganz links am Verstärker, neben dem Phono Eingang und ist mit "ground" gekennzeichnet.

 

Wenn Sie alle Punkte erledigt haben, haben Sie Ihre Braun A1 oder A2 Stereoanlage optimal verkabelt.

Jetzt können Sie die Geräte einschalten und testen.

Oft herrscht jetzt hinter den Klappen "Platznot" und Kabel Chaos. Daher haben wir ein extra kurzes Cinch Kabel Set entwickelt, welches optimal zu Ihrer Braun Atelier Anlage passt. Dies können Sie hier erwerben.

Wir wünschen Ihnen viel Freude beim Musikhören mit Ihrer Braun Atelier Anlage.

Sollten Sie Fragen zum Anschluß Ihrer Anlage haben, kontaktieren Sie uns gerne.

Am Ende des Artikels finden Sie noch ein paar Bilder, die die Verkabelung zeigen.

English Version:

There are also a few things to consider when wiring the Braun system to the A1 or A2 amplifier.

Due to the many requests, I present the correct cabling in this article.

As always, a few basic things first:

- first of all turn off all devices before starting wiring

- for the right channel we use the red cinch plugs for wiring - for the left channel we use the black ones

- on the Braun Atelier devices, the sockets for the right channel are at the bottom - those for the left channel are at the top

- red for the "+" contact and black for the "-" contact on the loudspeakers; please make sure that you always connect correctly (i.e. + with + and - with -)

The following devices are shown in the pictures in this article (from bottom to top):

CD player, cassette deck, tuner, amplifier, turntable. The type of device is irrelevant - here I describe the wiring for a typical Braun Atelier Series 1 or 2 system, as I also offer it in my shop (click here).

 

Connecting the CD player:

The cinch connections of the CD player (e.g. Braun CD2, CD2/3, CD3, CD4 or CD5) are connected to the corresponding inputs on the amplifier. To do this, simply use the AUX connection on the Braun A1 or Braun A2 - or if you have an A2 amplifier from the latest series, you can also use the CD input.

If you have a CD3, then it is best to use the FIXED output on the CD3. This provides a stable signal. The variable output next to it can (and must) be controlled via the controller next to it.

 

Connection of the cassette deck / tape deck:

You can connect the cassette deck to Tape 1 or Tape 2.

This device has 4 cinch sockets on the back: 2 outputs (signal goes to the amplifier) ​​and 2 inputs (signal comes from the amplifier if you want to record something, for example). The outputs (output) on the cassette deck are connected to the inputs (Tape 1 in) on the Braun A1 or Braun A2. The inputs on the cassette deck (input) are connected to the outputs on the amplifier (Tape 1 out). Make sure that you connect the right and left correctly with each other.

Connecting the tuner / radio:

As the name suggests, the tuner is connected to the tuner inputs on the amplifier. Since there are only 2 cinch sockets on the tuner (regardless of whether it's a Braun T1 or T2), you can't go wrong here.

So that the tuner can receive a radio signal, I recommend an FM antenna with an amplifier or a high-quality antenna cable if you have an antenna connection at home. You can find both here in my shop.

Connections on the amplifier:

Now connect the speakers to the appropriate terminals on the amplifier. Red = positive pole of the speakers, black = ground / negative. Usually one core of the speaker cable is marked (either ribbed or provided with a colored stripe). I always use this marked wire for the positive pole / the red terminal.

With the Braun amplifiers A1 and A2, the connections for the left loudspeaker are at the top and for the right loudspeaker at the bottom. Make sure that the cables do not touch each other. And only connect one loudspeaker per terminal. Also connect the speakers of a pair to speaker 1; if you use a second pair of loudspeakers, then this one on pair 2. So please do NOT, for example, put one (left) loudspeaker on pair 1 and the other (right) loudspeaker of a loudspeaker pair on pair 2.

On the amplifier A1 or A2 you should then press the switch for the corresponding pair of loudspeakers behind the flap (usually pair 1).

Turntable connection:

The turntable cables are permanently attached to the Braun turntables P1, P2, P3 and P4. Again, red is for the right channel and black is for the left channel.

These cables connect to the A1's phono input.

The A1 has 2 phono inputs: both are designed for MM systems. It is therefore up to you whether you connect the turntable to phono 1 or phono 2.

There are 2 different versions of the Braun A2:

the first version of the A2 (also called A2/1) has a phono MM and a phono MC input. Turntables with the MM system are connected to the Phono MM input - in other words, in the Braun world, the Braun turntables P1, P2, P3 and P4M.

The P4 with MC2E system is connected to the Phono MC input (recognizable by the lettering "Braun" on the headshell / above the pickup needle).

If you have a Braun A2/2, then it only has one phono input. You then switch between Phono MM and MC via the switch on the back. So simply set the switch according to your pickup system.

The connection cable of the turntable also has a "ground cable", i.e. a simple small cable without a cinch plug. This must be connected to the ground terminal of the amplifier. This is located on the far left of the amplifier, next to the phono input and is marked "ground".

 

When you have completed all points, you have optimally wired your Braun A1 or A2 stereo system.

Now you can turn on the devices and test them.

Often there is now chaos behind the flaps "lack of space" and cables. That's why we have developed an extra short cinch cable set that fits perfectly with your Braun Atelier system. You can purchase this here.

We hope you enjoy listening to music with your Braun Atelier system.

If you have any questions about connecting your system, please do not hesitate to contact us.

Here  you  find a few more pictures showing the wiring.

DSC04655_Kopie_3

 

DSC04656_Kopierichtige Verkabelung Anschluss der Braun Atelier AnlageRichtige Verkabelung Anschluss Braun Atelier A2 P3 T2 C2 CD3

richtiger Anschluss Braun Atelier Verstärker Tuner Plattenspieler CD Spieler Kassettendeck Lautsprecher

Gesamten Beitrag lesen